Periods and data states
Understand the state of a section, missing values, estimates, and comparison periods.
Before comparing two numbers, check the selected period, time zone, metric, and the state of the section that shows them.
The state of a section
Section titled “The state of a section”A section on an analysis screen keeps its title and its figure slots even when it has no data. When the section is not in its normal state, it adds a short state word and a line that says why. Only a section that could not be loaded replaces its content, and the rest of the screen stays.
| State word | Line shown | How to read it |
|---|---|---|
| No data | There are no records in this period. | Nothing was recorded for the period. This is different from a value of zero. |
| Small sample | The sample is too small to give a score and grade. | No score or grade is shown for this period. |
| Calculating | Waiting for judgment or still calculating. | The result is not ready. Check again later. |
| In progress | The period is not over, so the values are provisional. | The values can still change. |
| Collecting | Today’s values are still being collected. | Check again later for today’s final figures. |
| Confirmation on hold | Confirmation is on hold while a rejudgment runs. | The value is not confirmed while the rejudgment runs. |
| Incomplete pricing | Pricing is incomplete, so only a partial sum is shown. | See Cost. |
| Could not load | This section could not be loaded. | Use Retry in that section. |
| Not applicable | This item does not apply. | The item does not apply here. |
| After trial end | Values are shown up to the end of the trial. | Values after the end of the trial are not included. |
| Not comparable | The score rule versions differ, so these cannot be compared. | Do not compare the values across the rule change. |
| Locked | See below. | The content is not shown. |
A dash (—) in a figure means the figure has no value to show. A missing value is not a score of zero or a free cost.
Locked content
Section titled “Locked content”A locked row or section carries one of three lines:
- “You left the organization, so the content cannot be shown.”
- “The retention period has passed, so the content cannot be shown.”
- “The content is not shown in masquerade mode.” A band at the top of the page says that an operator is viewing as you.
Errors
Section titled “Errors”A failed read shows one of these sentences in the section:
- “You don’t have access to this view.”
- “This item could not be found.”
- “You can’t do this.” An action that a masquerade session cannot do is disabled and labeled “Not available in masquerade mode”.
- “This period is before the first period that has records.”
Provisional and confirmed
Section titled “Provisional and confirmed”A period carries the label Provisional or Confirmed. A value is provisional until its period is confirmed. See Scores and work status for corrections after confirmation.
Periods and time zones
Section titled “Periods and time zones”The period control offers Weekly and Monthly, and the range picker has presets such as Last 7 days and This month. A week runs from Monday to Sunday. “This …” shows the period up to today. The range picker has a Time zone selector with Current time zone; check the displayed range and time zone, especially near midnight.
While a period is running, a comparison reads “vs same point last week” or “vs same point last month”, which compares with the same point of the previous period. After the period ends, it reads “vs last week” or “vs last month”. Do not compare a running period with a full one.
Where a screen shows “Aggregated at” with a time beside Refresh, that time is when its figures were last aggregated.
Sessions that were not counted
Section titled “Sessions that were not counted”The Sessions card on Overview can show a dash with the line “Not counted for part of this period”. The activity heatmap shows “Session count not available” for the affected cells. In both cases the session count is unknown, not zero.
Costs are estimates converted at API prices, never a bill. A total appears only when every request has a price. Otherwise the screen shows the sum of the priced requests with how many requests it covers, for example “3 of 4 requests priced · partial sum”. Each estimate is labeled with its basis: Catalog list price, Claude Code reported, or Mixed. On Rightsizing, a plain $ is a catalog list-price amount, ~$ is a Claude Code estimate used as a fallback, and — means the cost evidence is unavailable. Tokens and currency are different units.
Reports
Section titled “Reports”A new report shows “Generating a new report” while the report and its narrative are written from the aggregated numbers, usually in 1 to 3 minutes; the page refreshes when it is done. For team calendar changes, read Team Report.